🚀 go-pugleaf

Witam
jestem w trakcie skladania htpc. żeby nie ciagac klawiatury, zakupilem
pilota, ktory w systemie jest widziany jako klawiatura. wciskanie na
pilocie przyciskow 1-0, gora, dol, ok - w efekcie widoczne jest jakbym
naciskal normalne klawisze na klawiaturze. ogolnie fajnie dziala to pod
xbmc, ale juz dla vdr nie - menu itd.
probowalem walczyc z lirc, ale to nie tedy droga.
jak moge "przechwycic" przyciski z odbiornika i zmapowac je na takie
jakie ja chce? znaczy jak przycisne "menu" zeby mapowane bylo na
przycisk "m" itp.

oto troche informacji o urzadzeniu:

[16418.555208] usb 6-2: new low speed USB device number 4 using uhci_hcd
[16418.758216] petalynx 0003:18B1:0037.0004: fixing up Petalynx Maxter
Remote report descriptor
[16418.758841] input: ELMAK.pl irMAKbd pl as
/devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.0/input/input14
[16418.759056] petalynx 0003:18B1:0037.0004: input,hiddev0,hidraw1: USB
HID v1.00 Mouse [ELMAK.pl irMAKbd pl] on usb-0000:00:1d.0-2/input0


cat /proc/bud/input/devices
...
I: Bus=0003 Vendor=18b1 Product=0037 Version=0100
N: Name="ELMAK.pl irMAKbd pl"
P: Phys=usb-0000:00:1d.0-2/input0
S: Sysfs=/devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.0/input/input14
U: Uniq=
H: Handlers=sysrq kbd mouse2 event12
B: PROP=0
B: EV=12001f
B: KEY=80000f afd037 bf004400 0 0 70001 10000 38007 ff9f63fa c140dfff
febeffdf ffefffff ffffffff fffffffe
B: REL=103
B: ABS=f01 0
B: MSC=10
B: LED=1f

Bus 006 Device 004: ID 18b1:0037 Petalynx Maxter Remote Control
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         8
  idVendor           0x18b1 Petalynx
  idProduct          0x0037 Maxter Remote Control
  bcdDevice            3.97
  iManufacturer           3 ELMAK.pl
  iProduct                1 irMAKbd pl
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           41
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower               40mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      0 No Subclass
      bInterfaceProtocol      0 None
      iInterface              0
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.00
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength     246
         Report Descriptors:
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0005  1x 5 bytes
        bInterval              10
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval              10
Device Status:     0x0000
  (Bus Powered)

jak moge przemapowac klawisze??
-- 
MaRc