🚀 go-pugleaf

ok. zaczalem po woli kombinowac.
sciagnalem src.tar.gz
dalej make w npppd, nie wywalilo zadnych bledow i
make install
wyedytowalem plik /tmp/npppd.conf:

#
# Simplest npppd.conf sample
#
# $Id: HOWTO_PIPEX_NPPPD.txt,v 1.1 2010/01/31 13:27:36 yasuoka Exp $

interface_list:                         tun0
interface.tun0.ip4addr:                 10.0.0.1

# IP address pool
pool.dyna_pool:                         10.0.0.0/25
pool.pool:                              10.0.0.128/25

# Authentication
auth.local.realm_list:                  local
auth.local.realm.acctlist:              /tmp/npppd-users.csv
realm.local.concentrate:                tun0

lcp.mru:                                1492
auth.method:                            mschapv2 chap
#auth.method:                           mschapv2 chap pap
#ipcp.dns_primary:                      192.168.4.20
#ipcp.dns_secondary:                    192.168.6.20
#ipcp.nbns_primary:                     192.168.4.20
#ipcp.nbns_secondary:                   192.168.6.20
#ipcp.assign_fixed:                     true
#ipcp.assign_userselect:                true

pptpd.enabled:                          false
pptpd.ip4_allow:                        0.0.0.0/0
#pptpd.listener_in:                     PPTP 192.168.0.1

# L2TP daemon
l2tpd.enabled:                          false
l2tpd.ip4_allow:                        0.0.0.0/0
#l2tpd.listener_in:                     L2TP 192.168.0.1
#l2tpd.purge_ipsec_sa:                  true
l2tpd.require_ipsec:                    false

# PPPoE daemon
pppoed.enabled:                                true
pppoed.interface:                      PPPoE bge1

proba odpalenia wywala, Permission denied :(
robie to z roota i dodatkowo dalem 666 na pliki w /tmp. tak do testu.

# /usr/sbin/npppd -h 
 

usage: npppd [-sDdh] [-c config_file]
         -d: increase debuglevel.  Output log to standard error.
         -c: specify configuration file.  default="/etc/npppd/npppd.conf".
         -s: adjust syslog level to be silent.
         -D: run as a daemon.
         -h: show usage.
# /usr/sbin/npppd -dc /tmp/npppd.conf 
 

2010-06-11 12:38:38:NOTICE: Starting npppd pid=20471 version=5.0.0
2010-06-11 12:38:38:ERR: Load configuration from='/tmp/npppd.conf' failed: 
Permission denied
2010-06-11 12:38:38:NOTICE: Terminate npppd.
#

# ls -al /tmp/ 
 

total 16
drwxrwxrwt   2 root    wheel   512 Jun 11 12:38 .
drwxr-xr-x  14 root    wheel   512 Jun 11 11:05 ..
-r--r--r--   1 _npppd  wheel   125 Jun 11 12:20 npppd-users.csv
-r--r--r--   1 _npppd  wheel  1483 Jun 11 12:34 npppd.conf

dlaczego mam permidion denied?