🚀 go-pugleaf

wywal_dodaj_krokpe pisze:
> pawell32 pisze:
>> Witam.
>>
>> Może i ten temat już był, lecz nie trafiłem dokładnie na to co
>> potrzebuje. Otóż przechodzę na Debiana, zaistalowałem 4.0 r6 64,
>> KDE 3.5.5, karta graficzna GF7300, i potrzebuje uruchomić obsługę dwóch
>> monitorów. W chwili obecnej obydwa monitory wyświetlają to samo, ale
>> potrzebuje większej przestrzenie roboczej.
>>
>> Pozdrwaiam
> Musisz sobie skonfigurowac odpowiednio xorg.conf, ja swego czasu na
> Debianie to robilem, niestety nie posiadam juz konfiga xorga z niego.
> 
> Na moim gentoo dzialam na dwoch monitorach, ale na kazdym z nich jest
> uruchomiona i sesja X-ów. Zapodaje konfiga, przerob sobie go dla
> wlasnych potrzeb.
> 
> 
> # nvidia-xconfig: X configuration file generated by nvidia-xconfig
> # nvidia-xconfig:  version 1.0  (buildmeister@builder58)  Wed Oct  1
> 15:12:53 PDT 2008
> 
> 
> Section "Module"
>     Load           "dbe"
>     Load           "extmod"
>     Load           "type1"
>     Load           "freetype"
>     Load           "glx"
> EndSection
> 
> Section "InputDevice"
>     # generated from data in "/etc/conf.d/gpm"
>     Identifier     "Mouse0"
>     Driver         "mouse"
>     Option         "Protocol"
>     Option         "Device" "/dev/input/mice"
>     Option         "Emulate3Buttons" "no"
>     Option         "ZAxisMapping" "4 5"
> EndSection
> 
> Section "InputDevice"
>     # generated from default
>     Identifier     "Keyboard0"
>     Driver         "kbd"
> EndSection
> 
> # Monitor section for CRT2 (master head
> #
> Section "Monitor"
> 
>         Identifier   "CRT2"
>         VendorName   "Monitor Vendor"
>         ModelName    "My CRT2 device"
> 
> # VertRefresh & HorizSync:
> # # This decribes CTZ2; if CRT2 is LCD or TV, the driver will ignore the
> # # values given here. You only need to set these if you use CRT2 as
> secondary
> # # (analog) VGA and your monitor does not support DDC2.
> #
> #
> 
> #        VertRefresh  60-75
> #        HorizSync    30-90
> EndSection
> 
> # Monitor section for CRT1 (slave head)
> #
> Section "Monitor"
>         Identifier  "CRT1"
>         VendorName  "Monitor Vendor"
>         ModelName   "My VGA monitor"
> 
> 
> # These values are actually used to determine the resolution/refresh rates
> # # to be used on CRT1! If your monitor supported DDC2, you can leave these
> # # out.
> #
>         VertRefresh 60-75
>         HorizSync   30-90
>         Option      "DPMS"
> EndSection
> 
> # ----------------------------------------------------------
> # # DEVICE sections
> # # ----------------------------------------------------------
> # # This section contains configuration data of the video card.
> #
> # # Device section for CRT2 (master head) --------------------
> #
> Section "Device"
> 
>         Identifier "SiS chip-1"
>         VendorName "SiS"  # Value does not matter
>         BoardName  "SiS"  # value does not matter
> 
>         Driver     "sis"
>         Option         "EnableSiSCtrl"   "yes"
>         #Option "ForceCRT2Type" "TV"
>         #
>         ## Since this is the driver section for CRT2, options for
> adjusting the TV
>         ## image (such as TVStandard, CHTVOverscan, etc) should be
> placed in this
>         ## section (and not the Device section for CRT1 below)
>         #
>         ## Generally: Set as many options as possible in this device
> section,
>         ## not the one for CRT1. CRT2 is initialized first (thus the term
> # "master head") and its settings rule in many cases over the one
> # # given in the slave device's (CRT1) section. The only exceptions for
> # # this rule are all gamma correction and Xv related options, see below.
> #
> # # For dual head mode, BusID has to be specified! Check this using lspci!
> #
>         BusID           "PCI:1:00:0"
> # "Screen" selects the screen number for this device in dual head mode
> # # Screen 0 is master (always CRT2)
> #
> #
>         Screen          0
> 
> EndSection
> 
> # Device section for CRT1 (Slave head) --------------------
> #
> Section "Device"
>         Identifier      "SiS chip-2"
> 
>         Driver          "sis"
> 
> # For dual head mode, BusID must be specified!
> #
>         BusID           "PCI:1:00:0"
> 
> # Generally: Set all the options you need in the master
> # # section, not here. See above. The only exeptions to this
> # # rule are all Xv and gamma correction related options, such as
> #         #Option "CRT1Gamma" "false"
> #                 #Option "StoredGammaBrightness" "1.1 1.1 1.1"
> #                         #Option "StoredGammaPreBrightness" "1.2 1.2 1.2"
> #                                 #Option "XvGamma" "1.0 1.2 0.8"
> #                                         #Option "XvDefault..."
> #
> #                                         # "Screen" selects the screen
> number for this device in dual head mode
> #                                         # Screen 1 is slave (always
> CRT1 = external VGA)
> 
>         Screen          1
>         Option         "EnableSiSCtrl"   "yes"
> EndSection
> 
> 
> # ----------------------------------------------------------
> # # SCREEN section(s)
> # # ----------------------------------------------------------
> # # This section defines the available resulutions and depths.
> #
> # # Screen section for CRT2 (LCD/Plasma/DVI-D, TV, VGA2/DVI-A)
> #
> 
> Section "Screen"
>         Identifier "Screen1"
>         Device     "SiS chip-1"
>         Monitor    "CRT2"
>         DefaultDepth 24
>         Option         "AddARGBVisuals" "True"
>         Option         "AllowGLXWithComposite" "True"
>         Option         "RenderAccel" "True"
>         Option         "AddARGBGLXVisuals" "True"
>         SubSection "Display"
>                 Depth     24
>                 Modes     "1024x768" "800x600" "640x480"
>         EndSubSection
> EndSection
> 
> # Screen section for CRT1 (VGA)
> #
> # # DefaultDepth must be identical to master screen if using Xinerama.
> # # Otherwise, depths can be different.
> # # A depth of 8 is not supported in dual head mode.
> # # Resolutions can be different.
> #
> Section "Screen"
>         Identifier "Screen2"
>         Device     "SiS chip-2"
>         Monitor    "CRT1"
>         DefaultDepth 24
>         Option         "AddARGBVisuals" "True"
>         Option         "AllowGLXWithComposite" "True"
>         Option         "RenderAccel" "True"
>         Option         "AddARGBGLXVisuals" "True"
> 
> 
>         SubSection "Display"
>                 Depth 24
>                 Modes "1024x768" "800x600" "640x480"
>         EndSubSection
> EndSection
> 
> 
> Section "ServerLayout"
>         Identifier      "Default Layout"
> 
> # Now enable dual head mode:
> #
>         Screen          "Screen1"
>         Screen          "Screen2" LeftOf "Screen1"
> 
> # This enables Xinerama. If you don't set this to "on", startx will spawn
> # # two indepentent X sessions. In Xinerama mode, both screens are virtually
> # # one screen and only one X session is started.
> #         Option          "Xinerama" "on"
> 
>                  InputDevice     "Keyboard0"
>                  InputDevice     "Mouse0"
> #                 InputDevice     "USB Mouse"
>                                  EndSection
> 
> #                                 Section "DRI"
> #                                         Mode    0666
> #                                         EndSection
> 
> 
> Section "Extensions"
>         Option "Composite" "Enable"
> EndSection
> 
> 


dzięki, przyjacielu - działa


pawell