🚀 go-pugleaf

Dnia Fri, 28 Sep 2007 14:27:47 +0200, kanold napisał(a):

> zobacz sobie do /etc/udev/rules.d/z25_persistent-net.rules

Wybacz, ale twoja odpowiedź nie jest na żadne z moich pytań. Dodatkowo
generuje pytania:
1. Po co (pytanie o cel): This file was automatically generated by the
/lib/udev/write_net_rules program, probably run by the
persistent-net-generator.rules rules file. 
2. Co (jaki program) korzysta z
zawartych tu danych? Czy polecenie ifconfig, które podaje dokładnie takie
same dane, z tym samym błędem dot. karty wifi, polegającym na złym
odczycie MAC-a tej karty? (z windy wiem ze MAC tej karty to ....2F-5A a
jak widać w tym pliku oraz w ifconfig jest to ......00-00)

Na wszelki wypadek podaję to co wygrzebałem w sysconfig i dmesg na temat
sieciówek, może będzie pomocne w analizie:

SYSLOG
Sep 11 14:10:33 net/hw-detect.hotplug: Detected hotpluggable network interface eth0
Sep 11 14:10:33 net/hw-detect.hotplug: Detected hotpluggable network interface eth1
Sep 11 14:10:33 net/hw-detect.hotplug: Detected hotpluggable network interface eth2
Sep 11 14:10:33 net/hw-detect.hotplug: Detected hotpluggable network interface lo
Sep 11 14:10:34 main-menu[1344]: INFO: Menu item 'netcfg' selected 
Sep 11 14:10:34 kernel: eth0: resetting device...
Sep 11 14:10:34 kernel: eth0: uploading firmware...
Sep 11 14:10:34 kernel: prism54: request_firmware() failed for 'isl3890'
Sep 11 14:10:34 kernel: eth0: could not upload firmware ('isl3890')
Sep 11 14:10:34 kernel: eth0: islpci_reset: failure
Sep 11 14:10:34 netcfg[8659]: INFO: ethtool ioctl on eth0 failed  
Sep 11 14:10:34 netcfg[8659]: WARNING **: couldn't determine MII ioctl to use for eth0  
Sep 11 14:10:35 netcfg[8659]: INFO: eth0 is not associated. Relegating to defwireless 
Sep 11 14:10:35 netcfg[8659]: INFO: ethtool ioctl on eth1 failed  
Sep 11 14:10:35 netcfg[8659]: INFO: eth1 is disconnected. (MII)  
Sep 11 14:10:35 netcfg[8659]: INFO: eth1 is not a wireless interface. Continuing. 
Sep 11 14:10:35 kernel: 0000:01:0a.0: tulip_stop_rxtx() failed
Sep 11 14:10:35 kernel: eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
Sep 11 14:10:35 netcfg[8659]: INFO: eth2 is connected.  


DMESG
eth0: ADMtek Comet rev 17 at 00019000, 00:0C:F6:0E:C3:87, IRQ 193.
8139cp 0000:01:0b.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp 0000:01:0b.0: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 201
eth1: RealTek RTL8139 at 0x9400, 00:0f:ea:be:b7:07, IRQ 201
eth1:  Identified 8139 chip type 'RTL-8100B/8139D'
[-]
eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver