🚀 go-pugleaf

dmesg



NTFS driver v1.1.22 [Flags: R/O]
NTFS: Reading super block failed
BIOS-provided physical RAM map:
hm, page 000fb000 reserved twice.
hm, page 000fc000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
Memory: 515480k/524224k available (1469k kernel code, 8356k reserved, 609k
data, 92k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check reporting enabled on CPU#0.
CPU0: AMD Athlon(tm) XP 1800+ stepping 02
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
testing the IO APIC.......................
.......    : physical APIC id: 02
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
..... host bus clock speed is 266.6878 MHz.
All processors have done init_idle
PCI: Probing PCI hardware
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
SERIAL_PCI enabled
  http://www.scyld.com/network/ne2k-pci.html
eth0: RealTek RTL-8029 found at 0xd400, IRQ 18, 00:00:1C:30:04:CB.
agpgart: Detected Via Apollo Pro KT266 chipset
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PDC20276: chipset revision 1
    ide2: BM-DMA at 0xd800-0xd807, BIOS settings: hde:pio, hdf:pio
    ide3: BM-DMA at 0xd808-0xd80f, BIOS settings: hdg:pio, hdh:pio
VP_IDE: chipset revision 6
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
hda: CRD-8400C, ATAPI CD/DVD-ROM drive
hdb: HL-DT-ST GCE-8481B, ATAPI CD/DVD-ROM drive
hdc: FUJITSU MPE3136AT, ATA DISK drive
hde: WDC WD400JB-00ENA0, ATA DISK drive
hdg: WDC WD400JB-00ENA0, ATA DISK drive
hdc: attached ide-disk driver.
hdc: 26688576 sectors (13665 MB) w/2048KiB Cache, CHS=26476/16/63
hde: attached ide-disk driver.
hde: host protected area => 1
hde: 78165360 sectors (40021 MB) w/8192KiB Cache, CHS=77545/16/63, UDMA(100)
hdg: attached ide-disk driver.
hdg: host protected area => 1
hdg: 78165360 sectors (40021 MB) w/8192KiB Cache, CHS=77545/16/63, UDMA(100)
hda: attached ide-cdrom driver.
hda: ATAPI 40X CD-ROM drive, 128kB Cache
hdb: attached ide-cdrom driver.
hdb: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache
Partition check:
 hdc: hdc1 hdc2 hdc3
 hde: unknown partition table
 hdg: [PTBL] [4865/255/63] hdg1 hdg2 < >
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
usb.c: registered new driver hub
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
EXT3-fs: mounted filesystem with ordered data mode.
usb-uhci.c: $Revision: 1.275 $ time 14:03:17 Sep 13 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xc800, IRQ 21
usb-uhci.c: Detected 2 ports
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xc400, IRQ 21
usb-uhci.c: Detected 2 ports
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
hub.c: new USB device 00:10.0-1, assigned address 2
usb-uhci.c: interrupt, status 3, frame# 631
input0: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with
IntelliEye(TM)] on usb2:2.0
hub.c: new USB device 00:10.0-2, assigned address 3
md: multipath personality registered as nr 7
device eth0 entered promiscuous mode
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Tx timed out, cable problem? TSR=0x16, ISR=0x0, t=21.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Tx timed out, cable problem? TSR=0x16, ISR=0x0, t=21.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Tx timed out, cable problem? TSR=0x16, ISR=0x0, t=23.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Tx timed out, cable problem? TSR=0x16, ISR=0x0, t=21.
hdg3: bad access: block=0, count=1
end_request: I/O error, dev 22:03 (hdg), sector 0